BOILING POINT G1 Decreases going down. Because metal bonds get weaker. Less energy is required this metallic bonding. BOILING POINT G 17‚18 Increases. Because the atomic size incrases. The molecules are attracted by intermolecular forces. Going down the group‚ the intermolecular forces increases. More energy is needed to overcome these stronger forces. DENSITY Because mass increases faster than volume. REACTIVITY OF GROUP 1 The number of occupied shells increases. The atomic size increases
Free Atom Electron
5. Calculated mass of the sinker in ounces 1.74g Part C 1. Length of the foil 8.5cm 2. Width of the foil 8.5cm 3. Mass of the foil .60g 4. Volume of the foil .222 5. Thickness of the foil .0031 Part D 1. Boiling point of the ethanol 65ºc Part E 1. T¹ initial temperature 125ºc 2. T² final temperature 155ºc Post lab questions: 1. Based on my temperature value and my lab measurements‚ I calculated that the water density would be 2.16 (g/mL). This
Premium Density Kilogram Measurement
liquid in question is composed of compounds that differ in volatility such that their boiling points differ by at least 40 to 50 degrees Celsius. Because the very essence of simple distillation is relies upon the idea that more volatile compounds have lower boiling points and thus when heated to this boiling point will occupy most if not all of the vapor above the liquid pot residue. Because the difference in boiling point for the compounds in a mixed liquid must at least differ by 40 to 50 degrees Celsius
Premium Distillation Boiling point Temperature
Sample Lab Report for CHM 152 Name Lab Partner(s) Abstract: The physical properties‚ including the boiling point‚ density‚ and refractive index were measured for unknown liquid #16. The infrared (IR) spectrum of the compound was also taken. Based on the data collected‚ it was determined that the compound was likely to be salicylaldehyde. Introduction The purpose of this experiment was to determine the identity of an unknown organic liquid by measuring some of its physical
Premium Temperature Liquid Fundamental physics concepts
How do different liquids and solids affect the boiling and freezing point of water? Name 02/12/12 ABSTRACT There are many different substances that affect the freezing and boiling points of water. This experiment was designed to test the effects of five liquid and five solid substances/mixtures on the freezing and boiling points of water. It was hypothesized that if we tested five liquid and five solid substances/mixtures then the results would show that the solids would have a greater affect
Premium Water Temperature Melting point
Determination of Melting and Boiling Point of different Organic Compounds Bakare‚ Abimbola Kristine‚ C. Professor Miranda Marilyn‚ school of chemical engineering and biotechnology‚ Mapua Institute of Technology‚ CHM145L-B11 ABSTRACT A melting point of a solid is the temperature at which the first crystal just starts to melt until the temperature at which the last crystal just disappears. Thus‚ the melting point (m.p.) is actually a melting range. The melting point of a substance depends (usually
Premium Melting point Temperature Electron
distillation and gas chromatography based on their difference in boiling points. The boiling point of hexane is 69 degrees Celsius and the boiling point of toluene is 110 degrees Celsius. Three fractions were collected for both simple and fractional distillation. The first fraction was hexane since it had the lower boiling point. The second fraction was a mixture of toluene and hexane. The third fraction was toluene since it had the high boiling point of 110 degrees Celsius. Gas chromatography was also preformed
Premium Distillation Gas Water
Liquids & Solids Pre Lab Questions: 3pts 1. What are the learning goals of this lab? The learning goal of this experiment is to view and experience the melting point and boiling point of different substances. 2. Why is acetamide not allowed in contact with your skin? What precautions does one have to take to work with this chemical? Acetamide is a carcinogen‚ which can cause cancer. Therefore‚ it should not be allowed to come in contact with a person’s skin. Any person working with this chemical
Premium Temperature Liquid Fahrenheit
MELTING POINT AND BOILING POINT OF ORGANIC COMPOUNDS ------------------------------------------------- ABSTRACT The melting point (MP) and the boiling point (BP) are probably the most widely used physical constant in the field of science. Determining the boiling point and the melting point of a compound helps you to characterize an unknown solid in a quick‚ easy and cheap way. The temperature at which a compound turns from a solid state to a liquid state is known to be the melting point. On the
Premium Melting point Carboxylic acid Organic chemistry
Celsius) as water changed from solid to liquid to gas over a hot plate. This lab report will discuss quantitative and qualitative data contained in the lab‚ how energy is related to phase change in water and an elucidation of how melting point and boiling point relate to the physical properties of matter. This paper will basically outline the lab done in class and a way for the teacher to see what was learned from this lab. A real-life situation to this phase change of water is the glaciers that
Premium Temperature Boiling point