Lab #1: Projectile Motion Purpose: To determine experimentally the initial and final velocities of an air powered projectile. Hypothesis: If the angle of the rocket is launched at 45 degrees than the distance and velocity will maximize. Materials: Rocket launching platform Rocket launcher Rocket body Air pump Safety goggles Rubber washer Nose cone 40‚ 45‚ 50‚ 55 and 60 angle wooden blocks Measuring wheel Procedure: 1. The rocket was assembled by the rocket launcher
Premium Rocket Hypothesis
Errors and Uncertainty in Experimental Data Causes and Types of Errors Conducting research in any science course is dependent upon obtaining measurements. No measure is ever exact due to errors in instrumentation and measuring skills. If you were to obtain the mass of an object with a digital balance‚ the reading gives you a measure with a specific set of values. We can assume that the actual measure lies either slightly above or slightly below that reading. The range is the uncertainly of
Premium Measurement
Patel Nil Period 7 05/09/13 Static and Kinetic Friction Objectives:- * Use a Dual-Range Force Sensor to measure the force of static friction. * Determine the relationship between force of static friction and the weight of an object. * Measure the coefficients of static and kinetic friction for a particular block and track. * Use a Motion Detector to independently measure the coefficient of kinetic friction and compare it to the previously measured value. * Determine if the
Premium Friction Force Classical mechanics
Height of Ball Drop v/s The Depth of the Crater | By Tejas Shah‚ IBDP Year 1 | | | | | | | * Aim- To find the relationship between the depth of crater and the height from which it is dropped. * Research Question- Does the height from where the ball is released affect the depth of the crater. * Hypothesis- If we increase the height of the drop of the ball; the depth of the crater would increase. This is because as there is loss in potential energy subsequently there
Premium Kinetic energy Energy Potential energy
Introduction The purpose of this lab is to examine the motion of an electron‚ when it encounters a constant magnetic and electric field. We will also observe when the electric field and magnetic field will cancel each other out. This will lead to the electron having no net force acting upon it. By adjusting the values for the magnetic and electric fields‚ we will be able to check the different paths the electron follows. From this data we will be able to calculate the charge-to-mass ratio. Then
Premium Chemistry Electron Magnetic field
IB Physics Internal Assesment – Design Aspect 1: Focused problem: Investigate the relationship between the surface area of a circular hole and the time water takes to drain through it. Variables: Independent: Surface area of the hole Dependent: Time water takes to drain Fixed: Amount of Water Container Environmental Conditions Aspect 2: Control of the Variables The independent variable in this case is the surface area of the hole‚ and the dependant will be the time water takes
Premium Bottle
Experimental Report Aim The objective of the laboratory report was to determine the thermal expansion coefficient of copper and other materials by measuring the relative change in length of bars of the materials as a function of temperature. Introduction The average coefficient of thermal expansion α over a temperature interval ΔT is given by ΔL / L0 = ΔT Where L0 is the length at some initial temperature‚ and ΔL is the change in length corresponding to a change in temperature
Premium Thermodynamics
AL Physics Centripetal Force(1ST Lab Report) Objective : To measure the centripetal force by whirling it around a horizontal circle‚ then compare the result with theoretical value FC = m(2r. Apparatus : 1Rubber bung 1Glass tube (About 15 cm long) 1Slotted weights‚ with hanger 12 × 0.02 kg 1Nylon thread 1.5 m 1Paper marker 1Adhesive tape 1Metre rule 1Stop watch 1Safety goggles Set-up: Procedure: 1. Attach one end of a 1.5 m length of nylon thread to a rubber bung and thread
Premium Force Classical mechanics Mass
Science in the Big City: Exploring Career Opportunities in the Natural and Physical Sciences New York City May 13-18‚ 2014 Students in the Natural Sciences at the University of Houston-Downtown are generally accomplished and motivated students with strong interests in science. However‚ students typically have a very limited perception of the science careers available to them outside of medicine. To educate students as to the array of potential careers available in the sciences (not medicine)
Premium New York City Natural science Nature
Independent Assessment Physics Lab (SL): Cantilever Flexion Cherno Okafor Mr. Ebrahimi SPH4U7 October 21st‚ 2012 Introduction Purpose: The purpose of this Physics Lab is to investigate what factors determine the amount of flexion of the cantilever. Hence‚ the objective is to establish a relationship between the length of a cantilever‚ which may give some insight into the physics of cantilevers. Hypothesis: If one increases the length of a cantilever‚ one would expect there to be an
Premium Orders of magnitude Mass Force