measured and recorded by the class. These measurements were to determine error in measurements and the derived quantities‚ volume and density. The diameter was determined using a dial caliper and the mass‚ a triple beam balance. The results of the error for diameter were not as expected while the results of the volume and density were deviated greatly from expectations; only the weight had a small error. Experimental Instruments: 1. Steel ball 2. Dial caliper (Mano Stat Corp.) 3. Triple
Premium Standard deviation Measurement Fundamental physics concepts
Experiment 4: Experimental Errors and Uncertainty Brett R. Spencer Date Performed: June 10th‚ 2015: 3:10 p.m. PHY 111C02 Section 1: Experiment and Observation Time‚ t (s) Dist. Y1 (m) Dist. Y2 (m) Dist. Y3 (m) Dist. Y4 (m) Dist. Y5 (m) Mean of Y Standard Dev. t^2 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.50 1.00 1.40 1.10 1.40 1.50 1.28 0.22 0.25 0.75 2.60 3.20 2.80 2.50 3.10 2.84 0.30 0.56 1.00 4.80 4.40 5.10 4.70 4.80 4.76 0.16 1.00 1.25 8.20 7.90 7.50 8.10 7.40 7.82
Premium Statistics Standard deviation Arithmetic mean
Experimental Errors and Uncertainty Data: The data table that follows shows data taken in a free-fall experiment. Measurements were made of the distance of fall (Y) at each of the four precisely measured times. Time‚ t (s) Dist‚ y1 (m) Dist‚ y2 (m) Dist‚ y3 (m) Dist‚ y4 (m) Dist‚ y5 (m) <y> σ t2 0 0 0 0 0 0 0.5 1.0 1.4 1.1 1.4 1.5 0.75 2.6 3.2 2.8 2.5 3.1 1.0 4.8 4.4 5.1 4.7 4.8 1.25 8.2 7.9 7.5 8.1 7.4 Procedures From the above data perform the following Tasks. Task 1. Complete
Premium Measurement General relativity Analytic geometry
PK – Lab Report Name: ____________________ Section: ___________________ Experimental Errors and Uncertainty Data: The data table that follows shows data taken in a free-fall experiment. Measurements were made of the distance of fall (Y) at each of the four precisely measured times. Time‚ t (s)|Dist‚ y1 (m)|Dist‚ y2 (m)|Dist‚ y3 (m)|Dist‚ y4 (m)|Dist‚ y5 (m)||σ|t2| 0|0|0|0|0|0|0|0|0| 0.5|1.0|1.4|1.1|1.4|1.5|1.3|.2|.25| 0.75|2.6|3.2|2.8|2.5|3.1|2.8|.3|.56| 1.0|4.8|4
Premium Measurement Acceleration Error
Experimental Errors and Uncertainty Data: The data table that follows shows data taken in a free-fall experiment. Measurements were made of the distance of fall (Y) at each of the four precisely measured times. Time‚ t (s) Dist‚ y1 (m) Dist‚ y2 (m) Dist‚ y3 (m) Dist‚ y4 (m) Dist‚ y5 (m) <y> σ t2 0 0 0 0 0 0 0.5 1.0 1.4 1.1 1.4 1.5 0.75 2.6 3.2 2.8 2.5 3.1 1.0 4.8 4.4 5.1 4.7 4.8 1.25 8.2 7.9 7.5 8.1 7.4 Procedures From the above data perform the following Tasks. Task 1. Complete
Premium Measurement Error Analytic geometry
Experiment 1: Errors‚ Uncertainties and Measurements Laboratory Report Department of Math and Physics College of Science‚ University of Santo Tomas Abstract With the use of the ruler‚ vernier caliper‚ micrometer caliper and electronic gram scale‚ the group was able to acquire different sets of measurements by measuring the sphere of unknown composition. The group then was able to compute its mean diameter‚ average deviation‚ average deviation of the mean‚ volume‚ mass and % percent error for
Free Measurement Volume
Experiment 1: Errors‚ Uncertainties and Measurements Laboratory Report Abstract The success of an experiment greatly depends on how the group is able to execute it and how precise and accurate their results are. In this matter‚ errors and uncertainties in measurements are of great factor. In this experiment‚ the group was able to classify the causes of such errors and which measuring device is more precise and accurate than the other. These were obtained by measuring the diameter of an iron sphere
Premium Measurement
Experiment 1: Errors‚ Uncertainties‚ and Measurements Laboratory Report Margarita Andrea S. de Guzman‚ Celine Mae H. Duran‚ Celina Angeline P. Garcia‚ Anna Patricia V. Gerong Department of Math and Physics College of Science‚ University of Santo Tomas España‚ Manila Abstract Measurements‚ defined as a comparison with a standard‚ are essential in the study of physics. However‚ all measurements are prone to errors. There are two sources of errors: systematic errors random errors. This experiment
Premium Measurement
damage the spring. The spring will oscillate due to the acceleration‚ by using a stopwatch record the time taken for twenty complete oscillations. Then repeat this whole process with time same size of mass‚ you have to do two trials to narrow the uncertainty. Then add 100 g masses one by one to the mass hanger and record the extension of the spring and the time taken for that size of mass to complete twenty oscillations. You will be given an unknown mass and also record the time taken of that mass to
Premium Measurement Mass General relativity
Grade 11 physics: SPH3U1-01 | Physics Lab Report | Specific Heat Capacity of Brass | | Jin Jin Shi | 2012/12/6 | Instructor: Mr. Nailer | I. Introduction The amount of heat required to raise the temperature of a solid body depends on its change in temperature (ΔT)‚ its mass (m)‚ and an intrinsic characteristic of the material forming the body called specific heat (cp). The heat is calculated from the equation II. Purpose The purpose of this laboratory is to determine
Premium Heat Specific heat capacity Thermodynamics