Purpose: The purpose of this lab was to determine the freezing point of pure water‚ the experimental van’t Hoff factor for a substance and the molar mass of an unknown solution. Reagents: 25mL deionized Water ¼ to ½ inches of rock salt 25mL Sodium Nitrate (NaNO3 ) 25mL unknown solution – handle unknown solution carefully Procedure: For part 1‚ the freezing point of deionized water was determined. An ice bath was prepared by filling a 600mL beaker ¾ full of ice and covered with ¼ to
Premium Concentration Chemistry Water
Introduction The purpose of the experiment was to determine the melting points of compounds using a Mel-Temp device. The melting point of naphthalene‚ urea‚ and sulfanilamide are found. This is then followed by the measuring of an unknown compound‚ and an impure sample (a small amount of naphthalene mixed with the unknown). Experiment In the lab‚ the height of the chemical in the capillary was set to 2-3 mm thickness. The voltage at the Mel-Temp started at a low setting of 1.5-2. The heat was
Premium Temperature
Lab/ Chem 234 02/17/13 Lab 2: Melting Points Purpose: To determine the purity of a substance using melting point as physical property. We must also learn how to identify an unknown compound using its melting point. We got to identify an unknown compound using mixture melting point and finally we must learn to obtain an accurate melting point using Mel-Temp apparatus. Procedure: Set voltage to obtain the desired heating rate at the anticipated melting point range. The voltage control controls
Premium Temperature Fahrenheit Celsius
Crystallization and Melting Points Organic Chemistry 221 9/19/2012 Intro/Purpose: The purpose of this lab was to use crystallization to separate a compound from a solvent and be able to choose the best solvent to do so. Then identify an unknown and verify purity using melting points. Solubility contributes to crystallization; because a solute has lower solubility at lower temperatures‚ which makes the solvent separate from the solution as a solid. This process is important to understand because
Premium Solubility Chemical polarity
Recrystallization and Melting Point of Benzoic Acid Organic Chemistry 1 10/4/12 Abstract Recrystallization was done to remove impurities from the sample. The percent recovery of benzoic acid during recrystallization is 23.02%. The difference between the pure and impure samples was observed by comparison of melting points. It was found that impure sample had a lower and wider melting point range of 120.1-122.2 (C). The pure sample melting point range was 121.3-122.5 (C). These ranges helped determine
Premium Solubility
filtration and melting point. Chm237 Abstract: Acetaminaphen was crushed then extracted for the active ingredient by mixing it with methanol. Then separated from the binders by centrifugation and a filtration technique using a Pasteur pipet packed with alumina. The remaining solvent was then evaporated to yield the solid analgesic(.2295g‚ 45.9% yield) which was collected by filtration and tested for the purity of the drug by the melting point determination. The melting point was (135-142
Premium Melting point Liquid Codeine
The percent yield of meso-1‚2-dibromo-1‚2-diphenylethane was calculated to be 66.36% and with a melting point of 235.1°C. Therefore‚ it can be concluded that this experiment was successfully conducted as the percent yield obtained is only 33.64% off from the equilibrium point‚ and because the melting point met the literature value. The percent yield for the product was less than 100%‚ indicating that were experimental errors‚ such as an undesirable side reaction‚ or more likely‚ an incomplete reaction
Premium Chemical reaction Chemistry Melting point
synthesis of Acetaminophen is based on the amine group of p-aminophenol being acetylated by acetic anhydride to form an amide functional group. Acetaminophen is isolated as a crude solid which is then recrystallized to purify the product. Using melting point determination the recovered products purity is identified and can be compared to the theoretical value. In this experiment 3.0g of p-aminophenol along with approximately 10ml of deionized water will be heated in a water bath regulated at 65-75
Free Melting point Chemistry Solid
Preparation and melting point of Aspirin Aspirin is a painkilling drug and is produced worldwide to reduce and stop pain. Aspirin is made up of ehtanoylation of 2-hydroxbenzenecarboxylic acid in a presence of phosphoric acid. AIM: The aim of the experiment is to prepare and produce aspirin as pure as possible. I will do this threw preparing the aspirin and purifying the product threw recrystallization. I will then obtain a melting point of my product to get an estimate of its purity. By the end
Premium Thin layer chromatography Purity Liquid
Lab #1: Melting Points of Organic Compounds Report Form May 15‚ 2014 1. A “Melting Point Range” refers to the range of temperature at which a solid melts into its liquid state. 2. Pure compounds have narrow or ‘sharp’ melting point ranges‚ 1°C or less if the compound is very pure. A less pure compound exhibits a broader melting point range‚ between 3°C to 10°C as well as a depressed or lower range. 3. Crushing the sample allows for greater surface area-to-volume ratio of the powder‚ this
Premium Temperature Thermodynamics Heat