Flame Test Lab Morgan Chemistry CP 5/30/14 Abstract- In the flame test lab‚ the flame test was performed to excite the electrons in the samples and observe the color of the flame. The flame emits a color because each element has an exactly defined emission spectrum‚ which one can use to identify them. For example‚ NaCl was highlighter yellow‚ Sr(NO3)2 was sun orange‚ CuCl2 was turquoise‚ LiCl was neon red‚ KCl was solar flare yellow‚ and BaCl2 was Voldemort green. Introduction- In Bohr’s
Premium Chemistry Potassium Gas
Background In the Flame test lab we took a simple wire‚ looped it‚ and rinsed it in HCL (Hydrochloric Acid ). Then we dipped the wire in the different samples provided. The samples provided were Sodium‚Potassium‚Calcium‚ Barium‚ Strontium‚ Lithium ‚ and Copper II. Finally we put the wire loop into the flame of the bunsen burner. The flame erupted into many different colors for each specific sample. We then used the colors we recorded to find the two unknown samples given to us. But the question
Premium Oxygen Light Chemistry
Purpose: To use a set of standardized procedures to test for simple sugars and starch‚ proteins‚ and fats. Hypotheses: A.) B.) C.) Equipment: -Safety goggles -Lab apron -400 mL beaker -Utility stand with ring clamp -Hot plate -Thermometer -10 mL graduated cylinder -Test-tube racks -8 to 16 test tubes -Test tube holder -Medicine dropper -Rubber stoppers -Test-tube brush -Wax pencil -Distilled water
Premium Nutrition Cholesterol Starch
My partner and I were given unknown number 3 in the laboratory. After performing various tests over the course of a few weeks on our unknown‚ we came to the conclusion that our unknown organism is Klebsiella pneumoniae (K. pneumoniae). K. pneumoniae is a gram negative bacillus shaped microorganism. We observed that K. pneumoniae is a nonmotile organism. We performed multiple tests on our unknown culture‚ therefore we are very confident that it is correctly identified. We identified that K. pneumoniae
Premium Bacteria Microbiology Gram staining
This lab tests the process of germination with various pH levels. The pH level of something is its measure of acidity or how basic it is‚ solutions with a pH of less than 7 are said to be acidic‚ and solutions with a pH greater than 7 are said to be basic. The tap water that was used to water our beans had a pH of 6. In this lab‚ we studied the process of germination (the process by which a plant grows from a seed). Certain environmental factors can cause or stop a seed’s germination‚ and these factors
Premium Seed Germination Water
During the lab experiment six different test were conducted. Each test consists of chemicals to be tested using 3 to 10 drops of the additive in order to observe a change. With any experiment you compose a hypothesis; where you make an educated guess. The hypothesis will primarily be‚ which base chemical will produce the greatest change based on the additive. Experiment 6.1 (Starch) when adding the three drops of Iodine to each tube observe the color change. When performing this test the chemical
Premium Chemistry Hydrochloric acid Chemical reaction
Testable Question: What will happen to different halide salts found in the body if various compounds are added to the halide? How will the halides react? Introduction: For this lab we tested 6 halide salts found in the body‚ and their reactivity when a compound is added. We tested the halides NaF‚ NaCl‚ KBr‚ KI‚ and two unknown halides. To find the reaction of the halide‚ we are adding drops of Ca(NO3)2‚ AgNO3‚ AgNO3 + Na2S2O3‚ and NaOCI + Starch to the halides. Each halide will be separated from
Premium Chemistry Water Oxygen
ions. Materials: Safety glasses 10 test tubes Test tube rack Paper Pencil 50 mL beaker Bunsen burner Nichrome wire Barium Nitrate Copper Nitrate Strontium Nitrate Lithium Nitrate Potassium Nitrate Sodium Chloride Calcium Nitrate Unknown solutions A‚B‚ & C Hydrochloric Acid Wash bottle (with distilled water) Procedure: 1. Label the test tubes with the names of the solutions and unknowns. 2. Place about 5 mL of each solution into each test tube‚ and 10 mL of Hydrochloric Acid into
Premium Metal Ammonia Potassium
A flame test is conducted when an element is burned and the flame produces a color different the starting flame color. When the coffee stirrer was put into the flame‚ the element’s atoms (from the solution of the stirrer) left the original level of energy. When the atoms fell back to ground level‚ they released photons in the form of colored flame. Using the flame test‚ unknown compounds can be identified when they are burned since each element has a specific color. (Douma‚ 2008). The color
Premium Potassium Color Emission spectrum
Verifying Differences Between Athletes’ Heart Rates And Non-Athletes’ Heart Rates By Using Step Test Introduction: Different people have different heart rates because of many reasons such as health condition‚ smoking‚ working out‚ among others. This step test is used to compare and figure out the differences between athletes’ heart rates and non-athletes’ heart rates before and after the test. Kuno Hottenrott stated that the normal average heart rate of people ranges from 40 to 100 beats per
Premium Heart rate