Report of Deflections of Beams and Cantilevers Summary: There are four parts in this big experiment‚ including deflection of a cantilever‚ deflection of a simply supported beam‚ the shape of a deflected beam‚ and circular bending. In these four parts‚ a same set of laboratory instrument and apparatus is used‚ concluding a bracket‚ a moveable digital dial test indicator‚ U-section channel‚ moveable knife-edge‚ and three material beams: brass‚ aluminum‚ and steel. The experiment methods‚ and fixed point
Premium Beam Theory Cantilever
Solid Mechanics Lab Report Experiment to determine the Young’s modulus of an aluminium cantilever beam and the uncertainties in its measurement 1. Abstarct: The young’s modulus E‚ is a measure of the stiffness and is therefore one of the most important properties in engineering design. It is a materials ratio between stress and strain: E=σε Young’s modulus is a unique value for each material and indicates the strength of that material as well as how it will deform when a load is applied.
Premium Measurement Beam Cantilever
responsible for making the pillbug habitat‚ taking them in and out of the habitat for our experiment‚ setting up the experiment setups for testing‚ and timing the experiment. In my opinion‚ I contributed a lot in my group. I did a majority of the lab proposal‚ and a substantial amount in the lab report. I was always the one getting up to gather our materials and pillbugs from the bins and making sure that our experiment was going as smoothly as intended. From this project‚
Premium Scientific method Project management Management
anindyajyotiroy@gmail.com TAX Total Remarks 4325866 Payment received-CHEQUE-43155242-1 3-MAY-13 Credit 1660.00 0.00 1660.00 Payment for subscriber 426144 PaymentsReceived : Total PaymentsReceived: 1. Cheques to be in favour of "M/s Beam Telecom Pvt Ltd". 2. We do not accept out station cheques and post dated cheques. 3. In case of cheque bounce‚ Rs.100/- penalty will be levied. 4. 18% interest will be levied on overdue payments 5. In case of overdue/ defaults‚ the right to deactivate
Premium
EXPERIMENT 2 Title : Shear Force and Bending Moment Objective : To determine the shear force and bending moment when concentrated load‚ symmetrical load and non symmetrical load are applied Introduction The shear force (F) in a beam at any section‚ X‚ is the force transverse to the beam tending cause it to shear across the section. The shear force at any section is taken as positive if the right-hand side tends to slide downwards relative to the left hand portion. The negative force
Premium Force Shear stress Torque
Osmosis Experiment Dennis M. Feliciano Grand Canyon University BIO100L Biology Concepts Lab June 25‚ 2011 Osmosis Experiment Materials Grapes (unblemished) Raisins (larger is better) Water Salt Four small containers (i.e.‚ drinking cups or clear glasses) A metric ruler Methods and Procedure Place 1 cup (236 ml) of water in each of the 4 containers. In 2 of the containers‚ add 1 tablespoon (14.8 ml) of table salt and mix well. Measure the length and width of a raisin and place
Premium Osmosis Chemistry Concentration
INTRODUCTION Basic structural learning begins with an analyzing of a simply supported beam. A beam is a structural member (horizontal) that is design to support the applied load (vertical). It resists the applied loading by a combination of internal transverse shear force and bending moment. An accurate analysis required in order to make sure the beam is construct without any excessive loads which affect its strength. A bending moment exists in a structural element when a moment is applied to the element
Premium Force Shear stress
of the beam and in most cases are assumed to be equally or uniformly distributed. a- Uniformly distributed load. a- Uniformly varying load. Concept of Shear Force and Bending moment in beams: When the beam is loaded in some arbitrarily manner‚ the internal forces and moments are developed and the terms shear force and bending moments come into pictures which are helpful to analyze the beams further. Let us define these terms Now let us consider the beam as shown
Premium Force Shear stress
Surface Tension Steven Brignol Dr. Payne September 15 Introduction: Water’s ability to stick to itself is surface tension. In this lab we were able to measure and detect surface tension by dropping water‚ drop by drop‚ onto a penny. The quantity of droplets that fit on the penny was impressive. Hypothesis: The detergent will thicken the water making a tighter surface tension. Prediction: If soap increased the surface tension‚ then expansion will happen. Materials: (1) Pipette (2) Water
Premium Liquid Experiment
Derricka Joe Period 5 1 Oct.‚ 2014 Lab Experiment One: Physical Properties Lab Analysis: For our first unknown‚ we observed the color and odor of the substance. The substance was a clumpy‚ white‚ crystal-like substance and it smells like new plastic. When we tested the solubility in water it resulted insoluble and in ethanol it resulted soluble. This substance could not be tested for electrical conductivity because the water was insoluble. We then tested for the PH value and it was neutral. The
Premium Oxygen Water Ethanol