instractor
Lab 2.8.1: Basic Static Route Configuration (Instructor Version)
Topology Diagram
Addressing Table
Device
Interface
IP Address
Subnet Mask
Default Gateway
R1
Fa0/0
172.16.3.1
255.255.255.0
N/A
S0/0/0
172.16.2.1
255.255.255.0
N/A
R2
Fa0/0
172.16.1.1
255.255.255.0
N/A
S0/0/0
172.16.2.2
255.255.255.0
N/A
S0/0/1
192.168.1.2
255.255.255.0
N/A
R3
FA0/0
192.168.2.1
255.255.255.0
N/A
S0/0/1
192.168.1.1
255.255.255.0
N/A
PC1
NIC
172.16.3.10
255.255.255.0
172.16.3.1
PC2
NIC
172.16.1.10
255.255.255.0
172.16.1.1
PC3
NIC
192.168.2.10
255.255.255.0
192.168.2.1
Learning Objectives
Upon completion of this lab, you will be able to:
Cable a network according to the Topology Diagram.
Erase the startup configuration and reload a router to the default state.
Perform basic configuration tasks on a router.
Interpret debug ip routing output.
Configure and activate Serial and Ethernet interfaces.
Test connectivity.
Gather information to discover causes for lack of connectivity between devices.
Configure a static route using an intermediate address.
Configure a static route using an exit interface.
Compare a static route with intermediate address to a static route with exit interface.
Configure a default static route.
Configure a summary static route.
Document the network implementation.
Scenario
In this lab activity, you will create a network that is similar to the one shown in the Topology Diagram. Begin by cabling the network as shown in the Topology Diagram. You will then perform the initial router configurations required for connectivity. Use the IP addresses that are provided in the Addressing Table to apply an addressing scheme to the network devices. After completing the basic configuration, test connectivity between the devices on the network. First test the connections between directly connected devices, and then test connectivity between devices that are not directly connected. Static routes
Topology Diagram
Addressing Table
Device
Interface
IP Address
Subnet Mask
Default Gateway
R1
Fa0/0
172.16.3.1
255.255.255.0
N/A
S0/0/0
172.16.2.1
255.255.255.0
N/A
R2
Fa0/0
172.16.1.1
255.255.255.0
N/A
S0/0/0
172.16.2.2
255.255.255.0
N/A
S0/0/1
192.168.1.2
255.255.255.0
N/A
R3
FA0/0
192.168.2.1
255.255.255.0
N/A
S0/0/1
192.168.1.1
255.255.255.0
N/A
PC1
NIC
172.16.3.10
255.255.255.0
172.16.3.1
PC2
NIC
172.16.1.10
255.255.255.0
172.16.1.1
PC3
NIC
192.168.2.10
255.255.255.0
192.168.2.1
Learning Objectives
Upon completion of this lab, you will be able to:
Cable a network according to the Topology Diagram.
Erase the startup configuration and reload a router to the default state.
Perform basic configuration tasks on a router.
Interpret debug ip routing output.
Configure and activate Serial and Ethernet interfaces.
Test connectivity.
Gather information to discover causes for lack of connectivity between devices.
Configure a static route using an intermediate address.
Configure a static route using an exit interface.
Compare a static route with intermediate address to a static route with exit interface.
Configure a default static route.
Configure a summary static route.
Document the network implementation.
Scenario
In this lab activity, you will create a network that is similar to the one shown in the Topology Diagram. Begin by cabling the network as shown in the Topology Diagram. You will then perform the initial router configurations required for connectivity. Use the IP addresses that are provided in the Addressing Table to apply an addressing scheme to the network devices. After completing the basic configuration, test connectivity between the devices on the network. First test the connections between directly connected devices, and then test connectivity between devices that are not directly connected. Static routes