Chemical Gas Laboratory Tests
Chemical Gas Tests
Procedure
Part 1: Hydrogen and Manganese Dioxide
1. Inserted 4mL of hydrogen into a test tube
2. Scooped a little amount of manganese dioxide on the end of a wooden splint
3. Allowed the tip of the splint to flame using the Bunsen Burner
4. Allowed the reaction to proceed for a total of 15 seconds.
5. Placed the glowing splint into the test tube
6. Recorded the results
Part 2: Magnesium strip and Hydrochloric acid
1. Poured 3mL of hydrochloric acid into a test tube
2. Placed the magnesium strip into the hydrochloric acid into the tube and immediately covered the tube with a rubber stopper.
3. Allowed the magnesium strip to dissolve completely.
4. Carefully inserted a burning splint into the test tube.
5. Recorded the results.
Part 3: Vinegar and Sodium Bicarbonate (Baking Soda)
1. Poured 4mL of Vinegar into a test tube.
2. Lit the tip of a splint on fire using the Bunsen Burner.
3. Scooped a small amount of sodium bicarbonate.
4. Carefully added the sodium bicarbonate into the test tube.
5. Allowed the Vinegar and Baking Soda to react for 5 seconds.
6. Slightly tilted the test tube and inserted the burning splint halfway through.
7. Recorded the results.
Materials Used
Part 1: Hydrogen & Manganese Dioxide.
1. One test tube. 2. Hydrogen 3. Manganese Dioxide 4. One wooden splint 5. Bunsen Burner 6. Flint and Steel
Part 2: Magnesium strip and Hydrochloric acid
1. One test tube 2. One Magnesium strip 3. Hydrochloric acid 4. Rubber Stopper 5. Wooden splint 6. Bunsen Burner 7. Flint and Steel
Part 3: Vinegar and Sodium Bicarbonate (Baking Soda)
1. One test tube 2. Vinegar 3. Two splints 4. Baking Soda 5. Bunsen Burner 6. Flint and Steel
Observations
Type of Experiment Type of Splint Splints Reaction to Chemicals
Hydrogen & Mangenese DioxideOxygen | - glowing splint | - the glowing splint
Procedure
Part 1: Hydrogen and Manganese Dioxide
1. Inserted 4mL of hydrogen into a test tube
2. Scooped a little amount of manganese dioxide on the end of a wooden splint
3. Allowed the tip of the splint to flame using the Bunsen Burner
4. Allowed the reaction to proceed for a total of 15 seconds.
5. Placed the glowing splint into the test tube
6. Recorded the results
Part 2: Magnesium strip and Hydrochloric acid
1. Poured 3mL of hydrochloric acid into a test tube
2. Placed the magnesium strip into the hydrochloric acid into the tube and immediately covered the tube with a rubber stopper.
3. Allowed the magnesium strip to dissolve completely.
4. Carefully inserted a burning splint into the test tube.
5. Recorded the results.
Part 3: Vinegar and Sodium Bicarbonate (Baking Soda)
1. Poured 4mL of Vinegar into a test tube.
2. Lit the tip of a splint on fire using the Bunsen Burner.
3. Scooped a small amount of sodium bicarbonate.
4. Carefully added the sodium bicarbonate into the test tube.
5. Allowed the Vinegar and Baking Soda to react for 5 seconds.
6. Slightly tilted the test tube and inserted the burning splint halfway through.
7. Recorded the results.
Materials Used
Part 1: Hydrogen & Manganese Dioxide.
1. One test tube. 2. Hydrogen 3. Manganese Dioxide 4. One wooden splint 5. Bunsen Burner 6. Flint and Steel
Part 2: Magnesium strip and Hydrochloric acid
1. One test tube 2. One Magnesium strip 3. Hydrochloric acid 4. Rubber Stopper 5. Wooden splint 6. Bunsen Burner 7. Flint and Steel
Part 3: Vinegar and Sodium Bicarbonate (Baking Soda)
1. One test tube 2. Vinegar 3. Two splints 4. Baking Soda 5. Bunsen Burner 6. Flint and Steel
Observations
Type of Experiment Type of Splint Splints Reaction to Chemicals
Hydrogen & Mangenese DioxideOxygen | - glowing splint | - the glowing splint