HEAT AND MASS TRANSFER REPORT ON TRANSIENT HEAT CONDUCTION Submitted by CDT ARSHAD ALI CDT NIKHIL BHATIA Submitted to Associate Proffessor Pradeep Kumar Singh Indian Naval Academy Knowledge Begets immortality Certificate This is to certify that this project report entitiled “TRANSIENT HEAT CONDUCTION” by CDT ARSHAD ALI and CDT NIKHIL BHATIA during the academic year 2010-2014‚ is a bonafide record of work carried out under my guidance
Free Heat transfer Heat
Name: ______________________________________ Date: ________________________ Student Exploration: Heat Transfer by Conduction Vocabulary: conduction‚ convection‚ insulate‚ radiation‚ thermal conductor‚ thermal energy‚ thermal insulator Prior Knowledge Questions (Do these BEFORE using the Gizmo.) Suppose two frying pans have been left on the stove with the burners on. One of the frying pans has a metal handle and the other has a wooden handle. 1. Which handle do you think you could
Premium Heat Heat transfer Temperature
Heat and Energy Transfer Lab Materials needed: Part 1: bowls (not included in the lab kit; use cooking pots or plastic containers- something large enough to fit your hand) ice (not included in the lab kit) thermometers Part 2 test tubes – use three similar glasses or cups water various household materials for insulation stove or microwave to heat up water Part 1: Heat transfer and human sensation 1. Pour warm water in the bowl on the left‚ cold water in the bowl on the right‚
Premium Temperature Heat Insulator
this report is heat transfer in a concentric tube heat exchanger. A heat exchanger is a device used to transfer heat from a hot fluid to a colder fluid. Heat exchangers are widely used in the petroleum industry for various reasons. Some of the most important reasons are theta heat exchangers increase the process efficiency‚ conserve energy‚ reduce maintenance and provide employee safety among many other reasons. The main objectives of the lab study were to determine the heat transfer rate‚ the logarithmic
Free Heat transfer Heat Heat transfer coefficient
No. 1: Heat Pump Experiment 1. Objective The objective of the experiment is to measure the Coefficient of Performance (COP) of a Heat Pump. 2. The experimental setup The equipment provided is a heat pump with pressure and temperature sensors placed at various locations. 3. Procedure Study the diagram and equipment provided and identify the various components of the Heat Pump – that is‚ the compressor (1-2)‚ the condenser (2-3)‚ the expansion valve (3-4) and the evaporator (4-1)
Premium Heat exchanger Heat HVAC
Problems for heat integration 1. The stream data extracted from a specified section of a chemical process are given in Table 1 below. Table 1: Stream Data Stream Supply Temperature TS (oC) Target Temperature TT (oC) Heat Duty (MW) No Type H1 H2 H3 C1 C2 Hot Hot Hot Cold Cold 150 40 130 150 50 30 40 100 150 140 7.2 10 3 10 3.6 You are required to perform a heat recovery analysis for the plant section stated above. Given the Tmin for the
Premium Thermodynamics Energy conservation Energy
PERFORMANCE OF A HEAT EXCHANGER Student Name: Chai Shu Qian Student ID: 0317060 Group Members: 1. Aaron Yesudian A/L William Yesudian 2. Anis Raihana Binti Abdul Aziz 3. Choo Choong Onn 4. Lee Kim Weng School of Engineering Taylor’s University Malaysia 15 April 2014 Table of Content
Premium Heat transfer Heat Thermodynamics
Problelm 3.6 Given data: Thi := 250 °C Tci := 30 °C mh := 0.15 kg s mc := 0.6 kg s cph := 2000 J kg⋅ K cpc := 1000 J kg⋅ K U := 1000 W m K 2 Finding Heat Exchanger Area(A0): 2 Cc := mc⋅ cpc = 600 m ⋅ kg K⋅ s 3 Ch := mh⋅ cph = 300 m ⋅ kg K⋅ s 3 2 Tco := mh⋅ cph⋅ Thi + mc⋅ cpc⋅ Tci mh⋅ cph + mc⋅ cpc 4 = 103.333 °C Tho := Tco Q := Ch⋅ ( Thi − Tho) = 4.4 × 10 W Thi − Tco − ( Tho − Tci) Thi − Tco ln Tho − Tci Cc Ch Ch Cc ε0 := if ( Cc
Premium Heat transfer Trigraph Heat exchanger
Gambit and Fluent: Turbulent Flow and Heat Transfer in a Mixing Elbow 1.Abstract This exercise comprises of two sections A and B‚ where in the first section an analysis in creating initial vertices will be carried out along with the creation of edges and faces‚ and the setting of boundary types. The program used for this phase of the investigation will be Gambit. These will then be generated into a mesh using Fluent. Moreover‚ section B will focus on the sensitivity to the computational mesh
Premium Fluid dynamics Thermodynamics Velocity
Heat Exchanger Network Design for the Cumene Process | C.A.K.E. Because We’re Just that Delicious Iowa State University Ames IA‚ 50010 | Crego‚ Courtney LHines‚ KirkMonterrubio‚ AmyToohey‚ Erin | Abstract Often a major consideration of a chemical process plant is the high cost of utilities used for heating and cooling of process streams. Heat integration of process streams is an effective way to reduce the cost of these utilities‚ and this process is often referred to as a MUMNE (minimum
Premium Heat exchanger Heat transfer