MECHANICAL ENGINEERING 449 SENIOR LAB Test of a Heat Pump Submitted Submitted by: Submitted to: Executive Summary: The purpose of this experiment was to determine the performance values of a Hylton Air and Water Heat Pump System. The system uses refrigerant 134a and water as the working fluids. The power input of the system was measured. The rate of heat output and the coefficient of performance are to be determined
Premium Thermodynamics Heat Heat pump
HIGH ALBEDO HEAT REFLECTIVE PAINT Sunsheetal® is based on polyurethane-acrylic blended elastomeric aqueous polymers. It is a high thermal emittance ceramic coating useful in the world of industrial and commercial buildings‚ as a roof coating system that has the ability to reflect the visible‚ infrared and ultraviolet wavelengths of the sun‚ thereby reducing heat transfer to the building. Sunsheetal® is defined as a cool roof coating by virtue of its ability to radiate absorbed‚ or non-reflected
Premium Humidity Heat Temperature
Experiment no. 1 Group No./Time/Day:6/7:30-10:30/Wednesday I. Title: Specific Heat of Solids II. Object: To determine the specific heat capacity of solids by methods of mixtures. III. Apparatus: Lead and Iron shots‚ Electric heater‚ Calorimeter‚ Dipper‚ 2 Thermometers‚ Water bath‚ Set of Masses‚ Trip Scale balance‚ Extension cords
Premium Specific heat capacity Heat Thermodynamics
Investigation 11 Specific heat capacity Aim: Investigate to determine the specific heat capacity of a metal cube provided Apparatus: -thermometer -stirrer -water -calorimeter -beam balance -metal cube -beaker Procedure: Using the normal equipment for Thermal Physics investigations‚ you are required to design and carry out an investigation to determine the specific heat capacity of a metal cube provide by teacher. Furthermore‚ you will need to compare your obtained value with
Premium Specific heat capacity Thermodynamics Water
Marybeth Brooks Physics Lab III Specific Heat Capacity Lab May 25‚ 2011 Abstract The specific heat capacity of various metals can be calculated and compared to accepted literature values. Dropping heated metal samples into a calorimeter filled with water and then measuring the change in the temperature of the system accomplished this. The metal samples were heated in a boiling water bath and were assumed to be at 100 C when they were removed. It was added to a calorimeter and stirrer
Premium Heat Thermodynamics Temperature
Ten Minutes of Specific Heat Remi Adams East Rowan High School AP Environmental Science Abstract Specific heat and climate were the primary focus of this lab. Specific heat is defined as “the measure of the ability of a substance to change temperature”. The purpose for carrying out this lab was to determine the specific heat/rates of both soil and water‚ and then comparing them. Students also were to relate specific heat to climate. Students were to determine which substance expressed
Premium Specific heat capacity Heat Thermodynamics
Heat Exchanger Network Design for the Cumene Process | C.A.K.E. Because We’re Just that Delicious Iowa State University Ames IA‚ 50010 | Crego‚ Courtney LHines‚ KirkMonterrubio‚ AmyToohey‚ Erin | Abstract Often a major consideration of a chemical process plant is the high cost of utilities used for heating and cooling of process streams. Heat integration of process streams is an effective way to reduce the cost of these utilities‚ and this process is often referred to as a MUMNE (minimum
Premium Heat exchanger Heat transfer
Sameera Raziuddin Latent Heat of Fusion April 11‚ 2011 Abstract: A calorimeter‚ water at room temperature‚ ice‚ and a Pasco GLS Explorer were used in combination with a known value of the latent heat of fusion to create and carry out an experiment to determine the mass of an unknown amount of ice. Using the formula for latent heat of fusion‚ the mass of the ice was calculated to be 45.76g. The error of the carried out experiment was calculated to be 20.06%. Introduction:
Premium Temperature Energy Fundamental physics concepts
Module 1: Lesson 5 ASSIGNMENT (12 marks) Lesson 5 Assignment Part 1: Molar Heat Calculations (3 marks) 1. Calculate the molar enthalpy of the NaOH(aq) using the data obtained from this experiment. Show all your work. Answer: Specific heat capacity: 4.19 J/g∙°C 50.0 ml of 1.0 mol/L NAOH Initial temperature: 23.9 °C Final temperature: 32.9 °C Change in temperature: 9 °C Q = mc∆t = (80g)(4.19 J/g∙°C)(9°C) = 3016.8 J or 3.0168 kJ ∆rH = n∆rHm 3.0168 kJ = (0.05
Premium Thermodynamics Combustion Petroleum
Title: Specific Heat of Solids II. Object: To determine the specific heat capacity of solids by methods of mixtures. III. Theory: When to or more substances at different temperatures are mixed‚ heat will flow from the substance of higher temperature to the substance of lower temperature. The heat flow will continue until equilibrium in temperature is reached. From the Law of Conservation of Energy‚ whatever amount of heat is lost by the hot substance must be equal to the heat gained by the cold
Premium Heat Thermodynamics Temperature