virtual instrumentation
VIRTUAL INSTRUMENTATION OF PIN ON DISC INSTRUMENT
Bona fide record of work done by
K. VIGNESH (09P653)
S. VIMAL (09P654)
P. VISHNU RAM (09P655)
S. ARUN KUMAR (10P901)
Preliminary mini-project dissertation submitted in partial fulfillment of the requirements for the degree of
BACHELOR OF ENGINEERING (SANDWICH)
Branch: PRODUCTION ENGINEERING
Of Anna University, Chennai.
MACRH 2012
DEPARTMENT OF PRODUCTION ENGINEERING
PSG COLLEGE OF TECHNOLOGY (Autonomous Institution affiliated to Anna University, Coimbatore)
COIMBATORE – 641 004.
FACULTY GUIDE
CONTENTS
CONTENT Page No
ACKNOWLEDGEMENT
SYNOPSIS
LIST OF FIGURE
CHAPTER
1. INTRODUCTION...........………………………...……..………………………........1
1.1. VIRTUAL INSTRUMENTATION 1
1.2. LabVIEW 2
1.3. PIN ON DISC INSTRUMENT 3
2. LITERATURE SURVEY……………………..…………………………..………….5
3. PROBLEM DEFINITION AND OBJECTIVE……………………………......…….8
3.1 PROBLEM DEFINITION 8
3.2 OBJECTIVE 8
4. METHODOLOGY………………………………………………………….………....9
5. PROCEDURE AND RESULTS…………………………………...…..……10
5.1 Calibrating the Pin on Disc Instrument 10
5.2 Conversion of Time to Sliding Distance 11
5.3 Exporting Values to Spreadsheet File 12
5.4 Steps to Run the Program 13
6. CONCLUSION………………..………………………………..….…….....…...…...15
BIBLIOGRAPHY..........................................................................................................16
ACKNOWLEDGEMENT
We would like to express our sincere gratitude and profound thanks to Dr. R. Rudramoorthy, Principal, PSG College of Technology, for his inevitable encouragement and support.
We extend our profound gratitude to Dr. K. Prakasan, Professor and Head, Department of Production Engineering, PSG College of Technology, who has always been a source
Bona fide record of work done by
K. VIGNESH (09P653)
S. VIMAL (09P654)
P. VISHNU RAM (09P655)
S. ARUN KUMAR (10P901)
Preliminary mini-project dissertation submitted in partial fulfillment of the requirements for the degree of
BACHELOR OF ENGINEERING (SANDWICH)
Branch: PRODUCTION ENGINEERING
Of Anna University, Chennai.
MACRH 2012
DEPARTMENT OF PRODUCTION ENGINEERING
PSG COLLEGE OF TECHNOLOGY (Autonomous Institution affiliated to Anna University, Coimbatore)
COIMBATORE – 641 004.
FACULTY GUIDE
CONTENTS
CONTENT Page No
ACKNOWLEDGEMENT
SYNOPSIS
LIST OF FIGURE
CHAPTER
1. INTRODUCTION...........………………………...……..………………………........1
1.1. VIRTUAL INSTRUMENTATION 1
1.2. LabVIEW 2
1.3. PIN ON DISC INSTRUMENT 3
2. LITERATURE SURVEY……………………..…………………………..………….5
3. PROBLEM DEFINITION AND OBJECTIVE……………………………......…….8
3.1 PROBLEM DEFINITION 8
3.2 OBJECTIVE 8
4. METHODOLOGY………………………………………………………….………....9
5. PROCEDURE AND RESULTS…………………………………...…..……10
5.1 Calibrating the Pin on Disc Instrument 10
5.2 Conversion of Time to Sliding Distance 11
5.3 Exporting Values to Spreadsheet File 12
5.4 Steps to Run the Program 13
6. CONCLUSION………………..………………………………..….…….....…...…...15
BIBLIOGRAPHY..........................................................................................................16
ACKNOWLEDGEMENT
We would like to express our sincere gratitude and profound thanks to Dr. R. Rudramoorthy, Principal, PSG College of Technology, for his inevitable encouragement and support.
We extend our profound gratitude to Dr. K. Prakasan, Professor and Head, Department of Production Engineering, PSG College of Technology, who has always been a source
Bibliography: 1. F.J. Jimenez, J. De Frutos, “Virtual instrument for measurement, processing data, and visualization of vibration patterns of piezoelectric devices” Computer Standards & Interfaces 27 (2005) 653-663. 2. Giovanni Moschioni, “A Virtual Instrumentation System for Measurements on the Tallest Medieval Bell Tower in Europe” IEEE Transactions on Instrumentation and Measurement, Vol. 52, NO. 3, June 2003. 3. V. Anantha Subramanian, G. Ashokumar, V, Jagadeesh Kumar, “Active Fin Control for Yacht Using Virtual Instrumentation”, Ocean Engineering, Volume 34, Issues 3-4, March 2007, Pages 390-402. 4. Yin Jian, Liangyin Jiang, Ming Li, “Virtual Instrumentation For Motorized Spindle Performance Monitoring” 2010 International Conference on Computer, Mechatronics, Control and Electronic Engineering (CMCE). 5. Subhransu Padhee, Yaduvir Singh, “Data Logging and Supervisory Control of Process Using LabVIEW”, Proceedings of the 2011 IEEE Students’ Technology Symposium, 14-16 January, 2011, IIT Kharagpur. 6. Florin SANDU, Venetia SANDU, Stefan NAN, Adrian Iulian DUMITRU, “Data Acquisition and Virtual Instrumentation System for the Study of Peltier and Seeback Effects”, 2010, 12th International Conference on Optimization of Electrical and Electronic Equipment, OPTIM 2010. 7. E. Portillo, I. Cabanes, M. Marcos, D. Orive, J. A. Sanchez, “Design of a Virtual-Instrumentation System for a Machining Process”, IEEE Transactions on Instrumentation and Measurement, Vol. 56, No. 6, December 2007. 8. Changting Wang, Robert X Gao, “A Virtual Instrumentation System for Integrated Bearing Condition Monitoring”, IEEE Transactions on Instrumentation and Measurement, Vol. 49, No. 2, April 2000.