Preview

The Steam Turbine

Powerful Essays
Open Document
Open Document
4897 Words
Grammar
Grammar
Plagiarism
Plagiarism
Writing
Writing
Score
Score
The Steam Turbine
The Steam Turbine, Part I

The Steam Turbine by Sir CHARLES A. PARSONS, K.C.B. Best viewed with window no wider than the above line.

THE STEAM TURBINE In modern times the progress of science has been phenomenally rapid. The old methods of research have given place to new. The almost infinite complexity of things has been recognized and methods, based on a co-ordination of data derived from accurate observation and tabulation of facts, have proved most successful in unravelling the secrets of Nature; and in this connection I cannot but allude to the work at the Cavendish Laboratory and also to that at the Engineering Laboratory in Cambridge, and tot he association of Professor Ewing with the early establishment of records in steam consumption by the turbine. In the practical sphere of enginerring the same systematic research is now followed, and the old rule of thumb methods have been discarded. The discoveries and data made and tabulated by physicists, chemists, and metallurgists, are eagerly sought by the engineer, and as far as possible utilized by him in his designs. In many of the best equipped works, also, a large amount of experimental research, directly bearing on the business, is carried on by the staff. The subject of our lecture today is the Steam Turbine, and it may be interesting to mention that the work was initially commenced because calculation showed that, from the known data, a successful steam turbine ought to be capable of construction. The practical development of this engine was thus commenced chiefly on the basis of the data of physicists, and as giving some idea of the work involved in the investigation of the problem of marine propulsion by turbines, I may say that about 24,000 £ was spent before an order was received. Had the system been a failure or unsatisfactory, nearly the whole of this sum would have been lost. Further, in order to prove the advantage of mechanical gearing of turbines in mercantile and war vessels about 20,000 £

You May Also Find These Documents Helpful

  • Good Essays

    Steam engine: energy was in shortage so the steam engine became a necessary source for energy…

    • 923 Words
    • 4 Pages
    Good Essays
  • Satisfactory Essays

    Withers, Ernest. Milam and Roy Bryant. 23 September 1955. MDAH. Photograph. Web. 27 Feb. 2015.…

    • 763 Words
    • 4 Pages
    Satisfactory Essays
  • Powerful Essays

    Machinist Mate 2

    • 7421 Words
    • 30 Pages

    Textbook Assignment: “Introduction to the Machinist’s Mate (Surface) Rate” and “Steam Turbines,” chapters 1 and 2,…

    • 7421 Words
    • 30 Pages
    Powerful Essays
  • Best Essays

    [ 4 ]. Jones, A.H.M. Augustus. Edited by M.I. Finley. New York, New York: W.W. Norton & Company,…

    • 4578 Words
    • 19 Pages
    Best Essays
  • Powerful Essays

    Civic Engagement

    • 2882 Words
    • 12 Pages

    (1997): 243-63. EBSCOhost. The Haworth Press, Inc., 11 Oct. 2008. Web. 1 Oct. 2011. <http://www.tandfonline.com/doi/abs/10.1300/J083v28n03_08>.…

    • 2882 Words
    • 12 Pages
    Powerful Essays
  • Good Essays

    Many of the first textile mills and other factories were built in the New England region as there were a large number of fast flowing rivers which made it easy for the transportation of goods and they also had a large population. Later, Samuel Slater made many other spinning mills and also other factories in the Northeast side. Thus, the society turned into an urban society. This concentration of industries in the Northeast side had given ways to the development of transportation such as railroads, roadways and canals, which also encouraged business and trade in America. Canals played an important role in the transportation of the produced goods from one place to another. Eerie Canal was the first canal dug in the United States which allowed…

    • 1580 Words
    • 7 Pages
    Good Essays
  • Powerful Essays

    History.—s. 7, ch. 84-543; s. 7, ch. 84-553; ss. 21, 26, ch. 86-245; s. 4, ch. 91-429; s. 28, ch. 97-264; s. 113, ch. 2007-5.…

    • 838 Words
    • 4 Pages
    Powerful Essays
  • Better Essays

    STENGINES

    • 5727 Words
    • 18 Pages

    One of the most significant industrial challenges of the 1700's was the removal of water from mines. Steam power was used to pump the water from the mines. Now, this might seem to have very little to do with modern steam-powered electrical power plants. However, one of the fundamental principles used in the development of steam-based power is the principle that condensation of water vapour can create a vacuum. This brief history discusses how condensation was used to create vacuum for operation of early steam-based pumps, and how James Watt invented the separate condenser. Although the cyclic processes presented in this history are not used in today's continuous flow steam turbines, current systems use separate condensers operating at sub-atmospheric pressure, adapting the principles explained here. Also, the stories of the inventors and their inventions offer insight into the process of technological discovery. One of the most important principles applied in the operation of steam power is the creation of vacuum by condensation.…

    • 5727 Words
    • 18 Pages
    Better Essays
  • Good Essays

    A turbofan engine is found on all commercial airliners around the globe. The turbofan engine works by way of a thermodynamic cycle where air is taken into the engine, then compressed, combusted, expanded, and finally exhausted out of the engine. This creates thrust in the engine and causes the vehicle to propel forward or backwards. These steps are carried out by the five major engine components: the fan, compressor, combustor, turbine, and exhaust nozzle. The compressor and turbine contain high and low pressures. These components are shown in Figure 1. In Figure 2, it shows all the 5 main components of the engine starting from 1 and then towards the end to 5.…

    • 1008 Words
    • 3 Pages
    Good Essays
  • Satisfactory Essays

    of gas turbine technology will face, as well as promising gas turbine developments. The key topics to be addressed are:…

    • 5058 Words
    • 21 Pages
    Satisfactory Essays
  • Powerful Essays

    GTA believes that expanded government-sponsored research on improved gas turbine technology will lead to more American jobs going forward, increased American global competitiveness, and potential greenhouse gas reductions in the power sector.…

    • 13970 Words
    • 56 Pages
    Powerful Essays
  • Powerful Essays

    Quasi Turbine

    • 3035 Words
    • 13 Pages

    It is a new engine concept from Canada which offers a design similar to that of rotary engines but with the advantages of a gas turbine-all within the confines of a chamber based on the shape of a Saint Hilaire skating rink profile. Each Quasi turbine device is at the cross road of three modern engines: inspired by the turbines: it perfects the piston, and improves on the Wankel. The Quasi turbine results from a research initiated in 1993 aimed at unifying the compression and power turbine into one entity. This invention is a new hybrid engine concept, midway between the piston and the turbine engine which requires relatively few components such as stator with covers, rotating blades, rocking carriages, wheels, and joints. Quasi turbine is also an environmental friendly engine, which provides an engine concept free from atmospheric gas pollution, noise pollution, thermal pollution etc. In this engine efficiency stays constant and optimum no matter the power of the unit.…

    • 3035 Words
    • 13 Pages
    Powerful Essays
  • Powerful Essays

    Wind Mill

    • 3029 Words
    • 13 Pages

    Wind machines come in two basic types—horizontal axis or vertical axis machines. The illustration Fig. E21.2.1 shows a horizontal axis machine, the type most often seen. The blades and hub rotate as air streams by. The shape of the blades “channels” the air, and creates regions of higher and lower pressure that result in a net force being applied to the blade, which causes it to turn. This rotational motion represents mechanical energy that will eventually drive the generator to produce electricity. However, usually, the rotational speed of the turbine is less than the 60 Hz AC, so there is an arrangement of gears to change the speed. This axle, the gearbox, and generator arrangement is designated the drivetrain in Fig. E21.2.1.…

    • 3029 Words
    • 13 Pages
    Powerful Essays
  • Satisfactory Essays

    Steam Turbine

    • 409 Words
    • 2 Pages

    The steam turbine is design based on the Rankin Vapor Cycle shown in Figure 1…

    • 409 Words
    • 2 Pages
    Satisfactory Essays
  • Powerful Essays

    Reference Documents: 1.MPL for Steam Turbine Doc. No. :- 41330000488(TAPP3/64110/5516/SCH) 2.Scheme for speed measurement turbine and generator Doc. No. :- 41330098204(TAPP3/64110/5512/DN) 3.Write up on LRR for MSCV and AEOR Doc. No. :- 41330000481(TAPP3/64110/5661/DN) 4.OGA of TG control desk 6610 – PL – 9 Doc. No. :- 06560000403(TAPP3/64100/5724/GA) 5.OGA of TG control desk 6610 – PL – 10 Doc. No. :- 06560000404(TAPP3/64100/5725/GA) 6.Turbine controller – CJJ01 – Cubicle & Rack assembly diagram Doc. No. :- 36560001746(TAPP3/64100/5728/GA) 7.Turbine controller – CJJ01 – Signal Flow Diagram(SFD) Doc. No. :- ED-031027-SF-S105(TAPP3/64100/5729/WD) 8.Turbine controller – CJJ01 – Functional Diagram(FCD) Doc. No. :- ED-031027-FC-S105(TAPP3/64100/5729/WD)…

    • 3847 Words
    • 16 Pages
    Powerful Essays

Related Topics