Sample Lab Aggregates
ABSTRACT
The objective of these experiments is to determine specific gravity, absorption capacity, and fineness modulus of a f ine aggregate sample and to plot a gradation curve for the sample. The scope of the experiment was limited to one aggregate sample only. In determining the SSD and oven-dry weights needed for calculation of specific gravities, a conical mold was used to reach an SSD condition and the sample was later dried in an oven. Sieve analysis determined the particle size distribution by sifting the aggregate through a series of eight sieves of different sixes by use of a mechanical shaker. The results found are that the aggregate used has a Bulk Specific Gravity (SSD) of 2.552, which indicates a normal weight, and Absorption of 0.12516%. The fineness modulus is 1.92. These results show that the sample aggregate is fine with a u niform gradation that would not be ideal to use as the sole aggregate for a concrete mixture. TABLE OF CONTENTS
1.0 INTRODUCTION
1
2.0 M ATERIALS
1
2.1 Part A - Specific Gravity and Absorption of Aggregate
2.2. Part B - Sieve Analysis
1
1
3.0 E QUIPMENT
1
3.1 Part A - Specific Gravity and Absorption of Aggregate
3.2 Part B - Sieve Analysis
1
2
4.0 PROCEDURE
2
4.1 Part A - Specific Gravity and Absorption of Aggregate
4.2 Part B - Sieve Analysis
2
3
5.0 RESULTS
4
5.1 Part A - Specific Gravity and Absorption of Aggregate
5.2 Part B - Sieve Analysis
4
4
6.0 DISCUSSION
5
6.1 Part A -Specific Gravity and Absorption of Aggregate
5.2 Part B - Sieve Analysis
5
6
7.0 CONCLUSIONS
8.0 R EFERENCES
9.0 APPENDIX
A.
B.
C.
8
8*•
8
Discussion - Part A, #4 Calculations
Discussion - Part A, #5 Calculations
Lab Handout and Raw Data
8
8
8
I A,
\0 INTROD
This laboratory was divided into two parts (A & B). Part A looked at the affect water has on the specific gravity and absorption of the m ixture. Part B used sieves to d etermine
The objective of these experiments is to determine specific gravity, absorption capacity, and fineness modulus of a f ine aggregate sample and to plot a gradation curve for the sample. The scope of the experiment was limited to one aggregate sample only. In determining the SSD and oven-dry weights needed for calculation of specific gravities, a conical mold was used to reach an SSD condition and the sample was later dried in an oven. Sieve analysis determined the particle size distribution by sifting the aggregate through a series of eight sieves of different sixes by use of a mechanical shaker. The results found are that the aggregate used has a Bulk Specific Gravity (SSD) of 2.552, which indicates a normal weight, and Absorption of 0.12516%. The fineness modulus is 1.92. These results show that the sample aggregate is fine with a u niform gradation that would not be ideal to use as the sole aggregate for a concrete mixture. TABLE OF CONTENTS
1.0 INTRODUCTION
1
2.0 M ATERIALS
1
2.1 Part A - Specific Gravity and Absorption of Aggregate
2.2. Part B - Sieve Analysis
1
1
3.0 E QUIPMENT
1
3.1 Part A - Specific Gravity and Absorption of Aggregate
3.2 Part B - Sieve Analysis
1
2
4.0 PROCEDURE
2
4.1 Part A - Specific Gravity and Absorption of Aggregate
4.2 Part B - Sieve Analysis
2
3
5.0 RESULTS
4
5.1 Part A - Specific Gravity and Absorption of Aggregate
5.2 Part B - Sieve Analysis
4
4
6.0 DISCUSSION
5
6.1 Part A -Specific Gravity and Absorption of Aggregate
5.2 Part B - Sieve Analysis
5
6
7.0 CONCLUSIONS
8.0 R EFERENCES
9.0 APPENDIX
A.
B.
C.
8
8*•
8
Discussion - Part A, #4 Calculations
Discussion - Part A, #5 Calculations
Lab Handout and Raw Data
8
8
8
I A,
\0 INTROD
This laboratory was divided into two parts (A & B). Part A looked at the affect water has on the specific gravity and absorption of the m ixture. Part B used sieves to d etermine