Preview

Raymond mill several troubleshooting methods

Good Essays
Open Document
Open Document
382 Words
Grammar
Grammar
Plagiarism
Plagiarism
Writing
Writing
Score
Score
Raymond mill several troubleshooting methods
Raymond mill in the course of this malfunction , according to the following processing :

Raymond mill is a common fault : no less powder or flour production is low .
Causes: ( 1 ) Locks powder is not adjusted, Mifengbuyan , resulting powder suck . ( 2 ) blade wear and material shovel can not afford .
Remedy: ( 1 ) checking and adjusting locks sealed powder was found to be leaking at the blade . ( 2 ) Replace the blade .

Raymond Mill Troubleshooting II : refined powder too thick or too thin .
Causes: ( 1 ) analysis of turbine blades wear serious , can not afford grading effect. ( 2 ) fan flow inappropriate .
Remedy: ( 1 ) Replacement blade length appropriate off a small amount of solution into the wind turbine is too rough . ( 2 ) too small and should be increased inlet air volume .

Raymond Mill Troubleshooting III : Host current rise , local temperature rises , the fan current drops .
Reason: ( a ) feeding excess powder duct is blocked, poor exhaust pipes , circulating air heat so that the main current , machine temperature rises , the fan current drops .
Remedy: ( 1 ) reduce the feed rate to clear the air duct of accumulated powder . ( 2 ) open big I duct valves, temperature control of the material into the machine at 6 ℃ or less.

Raymond Mill Troubleshooting four : Raymond Host noise and have greater vibrations.
Reason: ( a ) feeding quantity small . Badly worn blade , shovel can not afford materials , anchor bolts loose. ( 2 ) the impact of large hard material , or non- material material layer ( 3 ) Roller grinding ring out of round deformed .
Remedy: ( 1 ) Adjust the feeding amount , replacement blade . ( 2 ) replacement of feed size . ( 3 ) replace the roller , grinding ring .

Raymond Mill five common faults : fan vibration .
Reason: ( a ) powder or worn blades on a plot of imbalance . ( 2 ) anchor bolts loose.
Remedy: ( 1 ) removal or replacement blades blade accumulated powder . ( 2 ) tighten the anchor bolts .

Raymond Mill

You May Also Find These Documents Helpful

  • Good Essays

    Crash Course in Density

    • 438 Words
    • 2 Pages

    a few possibilities for this to happen, such as the fuel pump failing, a fuel…

    • 438 Words
    • 2 Pages
    Good Essays
  • Powerful Essays

    Est1 Task 5

    • 3478 Words
    • 14 Pages

    Comply with ECF SB 01-00-34, Check visually for cracks on the Pitch Control Lever Support Yoke in the Blend radius area.…

    • 3478 Words
    • 14 Pages
    Powerful Essays
  • Powerful Essays

    Low Speed Wind Turbine

    • 12089 Words
    • 49 Pages

    | Myat Myat Doe, "Design and Manufacturing of Wind Turbine Blade," in Third GMSARN International Conference, Kunming, 2008.…

    • 12089 Words
    • 49 Pages
    Powerful Essays
  • Satisfactory Essays

    Once this happens, it can cause your steel belts to detach from the tire. Aside from aging, heat can also contribute to this factor.…

    • 433 Words
    • 2 Pages
    Satisfactory Essays
  • Good Essays

    beat it manually using the system for about 2-3 hours until the mixture is smooth…

    • 3427 Words
    • 14 Pages
    Good Essays
  • Better Essays

    Spartan Plastic Limited

    • 1745 Words
    • 6 Pages

    The main problem for the company is to facing the high scrap rate and quality of the product. Another reason is the machine breakdowns, every time the machines stopped and restarted will make scraps out from the machines. Last reason is to produce new product will cause high scrap rates. This scrap problem will cause to the continuous flow process as well.…

    • 1745 Words
    • 6 Pages
    Better Essays
  • Best Essays

    Emotional Disturbance

    • 1318 Words
    • 6 Pages

    have been suggested as possible causes, research has not shown any of these factors to be…

    • 1318 Words
    • 6 Pages
    Best Essays
  • Good Essays

    A weakness that occurred during this practical was when it came to the baking process,…

    • 409 Words
    • 2 Pages
    Good Essays
  • Powerful Essays

    Bap250.1 Mastering History

    • 2388 Words
    • 10 Pages

    companies from the expensive cutter heads blowing up as well as to ensure a more quality…

    • 2388 Words
    • 10 Pages
    Powerful Essays
  • Satisfactory Essays

    Hank Kolb

    • 326 Words
    • 2 Pages

    Lack of Motivation, this refers to Hamler’s statement that mistakes happens once in a while and there is actually nothing people are doing to guarantee that similar mistakes are not repeated.Lack of Quality Standards, this refers Simmons action vented the rejected cans by hand, when it should be done professionally using standardized equipments.…

    • 326 Words
    • 2 Pages
    Satisfactory Essays
  • Good Essays

    Not using the right tools for the job. Some jobs require special tools for the best outcome. Trying to paint with a cheap brush will leave you with uneven color and a sloppy looking finish. Trying to remove a special fastener with the wrong tool can cause irreperable…

    • 488 Words
    • 2 Pages
    Good Essays
  • Better Essays

    Grinding Machines

    • 2191 Words
    • 9 Pages

    GRINDING MACHINES Grinding is the process of removing metal by the application of abrasives which are bonded to form a rotating wheel. When the moving abrasive particles contact the workpiece, they act as tiny cutting tools, each particle cutting a tiny chip from the workpiece. It is a common error to believe that grinding abrasive wheels remove material by a rubbing action; actually, the process is as much a cutting action as drilling, milling, and lathe turning.…

    • 2191 Words
    • 9 Pages
    Better Essays
  • Powerful Essays

    Muda

    • 1912 Words
    • 8 Pages

    Over processing or incorrect processing. Taking unneeded steps to process the parts. Inefficiently processing due to poor tool and…

    • 1912 Words
    • 8 Pages
    Powerful Essays
  • Good Essays

    The Morrison Company

    • 1011 Words
    • 5 Pages

    o During the production process of the inlay more and more mechanical or technical defects occur, so that the process has to be halted and repeated.…

    • 1011 Words
    • 5 Pages
    Good Essays
  • Satisfactory Essays

    When every part works well, open the lock strode of the feeder conveyor, observing the stability of the vibrating amplitude (the amplitude allows 0.5mm decline, if decent more you should check out the material chute pressure warehouse and elastic adjustment system) and the current, the satisfaction requirement of feeding amount. Both the amplitude and the electric current are under the normal rating value, but the feeding amount cannot meet the requirement, you can hang the vibrator oblique downward to some degree, within 20 degree the biggest…

    • 338 Words
    • 2 Pages
    Satisfactory Essays