PROJECT PRASHANT
K.S.INSTITUTE OF
TECHNOLOGY
RAGHUVANHALLI BANGLORE
SEMINAR ON :
TWO WHEELER WITH PROPELLER SHAFT BY
REPLACING CHAIN AND SPROCKET WITH A
SET OF BEVEL GEARS
BATCH NO.20
PROJECT GUIDE : MR.M. NAGABHUSHANA ,ME(PH.D)
PROJECT MEMBERS :
MR. PRASHANT KUMAR SINGH
USN:1KS11ME075
MOB.9480942041
MR. PRANEETH.N.SANIL
USN:1KS11ME074
MOB:9945061150
MR. PRAJWAL.C.N
USN:1KS11ME073
MOB:9035715817
MR. PRADEEP.S
USN:1KS11ME071
MOB:7411256378
INTRODUCTION
This project is developed for the users to rotate the back
wheel of a two wheeler using propeller shaft. Usually in two wheelers, chain and sprocket is used to drive the back wheel.
But in this project, the engine is connected at the front part of the vehicle.
The shaft of the engine is connected with a long rod. The other side of the long rod is connected with a set of bevel gears. The bevel gears are used to rotate the shaft in
90degree angle. The Back wheel of the vehicle is connected with the bevel gear (Driven).Thus the back wheel is rotated in perpendicular to the engine shaft. Thus the two wheeler will move forward. According to the direction of motion of engine, the wheel will move forward or reverse. This avoids the use of chain and sprocket method.
3D
VIEW
2D VIEW
Methodology:
•Fabrication of bicycle frame
•Selection of drive shaft
• Placing of bevel gears
•To assemble the engine and all the fabricated materials on two wheeler
•To test and validate the system performance
Advantages:
Moderate operation costs
It avoids wear and tear of chain and sprocket
Shaft drives are quieter and more reliable
Drive system is less likely to become jammed
Disadvantages:
The system is quite heavier
Reference Books:
Design and Analysis of a Propeller Shaft of a Toyota Qualis by “Syed Hasan”.
Details From:
Newspapers
Website Referred:
www.seminarsonly.com
www.projectideasblog.com
TECHNOLOGY
RAGHUVANHALLI BANGLORE
SEMINAR ON :
TWO WHEELER WITH PROPELLER SHAFT BY
REPLACING CHAIN AND SPROCKET WITH A
SET OF BEVEL GEARS
BATCH NO.20
PROJECT GUIDE : MR.M. NAGABHUSHANA ,ME(PH.D)
PROJECT MEMBERS :
MR. PRASHANT KUMAR SINGH
USN:1KS11ME075
MOB.9480942041
MR. PRANEETH.N.SANIL
USN:1KS11ME074
MOB:9945061150
MR. PRAJWAL.C.N
USN:1KS11ME073
MOB:9035715817
MR. PRADEEP.S
USN:1KS11ME071
MOB:7411256378
INTRODUCTION
This project is developed for the users to rotate the back
wheel of a two wheeler using propeller shaft. Usually in two wheelers, chain and sprocket is used to drive the back wheel.
But in this project, the engine is connected at the front part of the vehicle.
The shaft of the engine is connected with a long rod. The other side of the long rod is connected with a set of bevel gears. The bevel gears are used to rotate the shaft in
90degree angle. The Back wheel of the vehicle is connected with the bevel gear (Driven).Thus the back wheel is rotated in perpendicular to the engine shaft. Thus the two wheeler will move forward. According to the direction of motion of engine, the wheel will move forward or reverse. This avoids the use of chain and sprocket method.
3D
VIEW
2D VIEW
Methodology:
•Fabrication of bicycle frame
•Selection of drive shaft
• Placing of bevel gears
•To assemble the engine and all the fabricated materials on two wheeler
•To test and validate the system performance
Advantages:
Moderate operation costs
It avoids wear and tear of chain and sprocket
Shaft drives are quieter and more reliable
Drive system is less likely to become jammed
Disadvantages:
The system is quite heavier
Reference Books:
Design and Analysis of a Propeller Shaft of a Toyota Qualis by “Syed Hasan”.
Details From:
Newspapers
Website Referred:
www.seminarsonly.com
www.projectideasblog.com