Parts:
Breadboard
DC Power Supply
Hand Held DMM
Test leads
Wire
220 Ω resistor
560 Ω resistor
1.0kΩ resistor
1. State Kirchhoff’s Current Law.
The algebraic sum of the currents entering a node is equal to zero.
2. What is the equation for the total current in a parallel circuit?
It= I1+I2+I3….
3. Determine the total current in the following nodes.
1) It= 2mA+4mA+6mA= 0.012x10^-3=12mA
2) I + I1+I3= I2
I= 2mA+4mA= 1mA
I= 1mA- 6mA
I= -5mA
4. Determine the total current in the following circuit.
It= I1+I2+I3= 10mA+20mA+40mA= 0.07 x 10^-3= 70mA
5. If VS = 10 V in the circuit above, what are the following voltages?
R1= V/I= 10V/10mA= 1000 x 10^3= 1kΩ R2= V/I= 10V/20mA= 500kΩ R3= V/I= 10V/40mA= 250kΩ
Vr1= IR= 10mA x 1kΩ= 10V Vr2= IR= 10mA x 500kΩ= 10,000 x 10^3= 10V Vr3= IR= 10mA x 250kΩ= 10,000 x 10^3= 10V
6. Download the Multisim file “Parallel2” from Doc Sharing, Week 4. Calculate the values below.
IT1=__49.2mA____ IR1=__10mA____ IR2=__17.9mA___ IR3=___21.3mA____
V1=___10V______ VR1=__10V_____ VR2=___10V______ VR3=__10V_______
Ir1= Vs/R1= 10V/1000Ω= 0.01 x 10^-3= 10mA
Ir2= Vs/R2= 10V/560Ω= 0.01785 x 10^-3= 17.9mA
Ir3= Vs/R3= 10V/470Ω= 0.021276 x 10^-3= 21.3mA
It= Ir1+Ir2+Ir3=10mA+17.9mA+ 21.3mA= 0.0492 x 10^-3= 49.2mA
V=IR V1= 10mA(1000Ω)= 10V V2= 17.9mA(560Ω)= 10V V3= 21.3mA(470Ω)= 10V
7. Using Multisim, simulate the circuit. Use the appropriate test equipment and measure the following values.
IT1=__0.049A____ IR1=__10mA__ IR2=_17.85mA__ IR3=_21.275mA__
V1=__10V______ VR1=_10V______ VR2=__10V_____ VR3=__10V____
8. Prototype the circuit below on the breadboard. Connect the circuit’s input to the variable +12 V supply. Turn on the DC power supply and use the handheld DMM to set it to +10V. Using the handheld DMM, measure the values below. Remember, to measure current, the handheld DMM must be in series with the resistor. Have the professor verify the circuit before applying power.
IT1=_75.1mA___ IR1=_10.4mA_____ IR2=__18.4mA_____ IR3=__47mA_____
V1=__10V______ VR1=___10V_____ VR2=____10V____ VR3=___10V_____
Ir1= Vs/R1= 10V/1kΩ= 0.01 x 10^-3= 10mA
Ir2= Vs/R2= 10V/560Ω= 0.01785 x 10^-3= 17.9mA
Ir3= Vs/R3= 10V/220Ω= 0.04545 x 10^-3= 45.4mA
It= 10mA+17.9mA+45.4mA= 0.0733 x 10^-3= 73.3mA
9. If using ELVIS, use the ELVIS DMM and verify that the following values match the handheld DMM measurements. If NOT using ELVIS, skip to step 10.
IT1=____________ IR1=____________ IR2=____________ IR3=____________
10. How do the measured values compare to the calculated value? Are there any significant differences (YES/NO)? If yes, why?
They were the same. No differences.
You May Also Find These Documents Helpful
-
1. Using the circuit below, calculate the following values. On the circuit drawing, indicate the polarities for each voltage and show the current direction.…
- 279 Words
- 2 Pages
Satisfactory Essays -
b. Using the color bands, calculate the resistance and tolerance and record your calculated value.…
- 452 Words
- 4 Pages
Satisfactory Essays -
A conductor is made of materials that have little opposition to the flow of charge. A conductor is made of metals like copper, silver, aluminum or gold. These types of metals allows for the easy flow of electrons. Wires are made of these materials.…
- 302 Words
- 2 Pages
Satisfactory Essays -
The idea behind the Superposition Theorem is that in a circuit that contains several independent sources, one wants to know the effects of a particular independent source acting alone. Basically the idea is to deactivate one all sources but one and calculated desired output values, then move on to the next source investigating the effects of each. Once you gather all these output values (current and voltage) you add them up and they should give you the same values as those measured through experimentation (DeCarlo, p. 121). Throughout the implementation of this idea of deactivating sources one uses previous methods of finding voltages and currents, such as: Node Voltage Method, Mesh Current Method, Current and Voltage Division, and Kirchoff's Current and Voltage Laws.…
- 525 Words
- 3 Pages
Good Essays -
This is a CLOSED BOOK test. You can consult the test paper, KU tables and the attached output ONLY. You may use an approved calculator.…
- 814 Words
- 4 Pages
Satisfactory Essays -
2.6 Series And Parallel Circuits . . . . . . . . . . . . . . . . . . . . . . . . . 9…
- 33813 Words
- 136 Pages
Powerful Essays -
Specific heat capacity of water is the energy it takes to increase the temperature of 1 kg of water by 1° whilst the latent heat capacity is the energy needed to turn 1kg of water into steam. In both cases it is heating up the water.…
- 379 Words
- 4 Pages
Satisfactory Essays -
• Design testing: Based on datasheet example circuit, I have used this circuit succesfully as part of many electronics projects…
- 486 Words
- 2 Pages
Satisfactory Essays -
Apparatus: DC power supply, milliammeters and ammeters, voltmeters, SPST switch, a “fused” connector, a 2-meter slide wire resistance, and mounted resistance spools.…
- 457 Words
- 3 Pages
Good Essays -
R3 10 K V (12V ) 10.4V 1.5 K 10 K R2 R3…
- 975 Words
- 4 Pages
Good Essays -
Try working on this example and interprete the results. Submit your assignment via the assignment panel.…
- 1722 Words
- 7 Pages
Better Essays -
What do you think are the differences between the essays that you wrote at secondary school and the essays that you will need to write at university? Make sure you think about style* when considering these differences.…
- 4988 Words
- 20 Pages
Good Essays -
3.1.4 Now, fix Vin at 10V and vary the load resistance RL with values shown in Table 2.2 below. Measure the output voltage Vout.…
- 600 Words
- 3 Pages
Satisfactory Essays -
An analog multimeter is a device that is composed of various meters combined. Such instrument can measure resistance, voltage and current. It is commonly known as volt-ohm meter or VOM. This device can also determine the continuity in a circuit and it measures with high accuracy. In this project, a VOM was built using the given parameters and tested it in various circuits. The knowledge in building this kind of instrument is very helpful for the students.…
- 1453 Words
- 6 Pages
Powerful Essays -
R E2, RC1 = R C2 and the magnitude of +VCC is equal to the magnitude of ?VEE. These voltages are measured…
- 6946 Words
- 28 Pages
Satisfactory Essays