Preview

Compressive Strength Changes with Salinity

Powerful Essays
Open Document
Open Document
893 Words
Grammar
Grammar
Plagiarism
Plagiarism
Writing
Writing
Score
Score
Compressive Strength Changes with Salinity
REPORT

REPORT

CONSTRUCTION MATERIALS & TECHNOLOGY
Study of compressive strength of concrete made using saline water
15th November 2012

CONSTRUCTION MATERIALS & TECHNOLOGY
Study of compressive strength of concrete made using saline water
15th November 2012

CONTENTS

1. Introduction………………………………….2 2. Objectives…………………………………….2 3. Methodology…………………………………3 4. Concrete Making……………………………..4 * Materials and sourcing………………….4 * Moulds…………………………………...4 * Blocks…………………………………….4 5. Compressive strength test…………………….5 * Results and graphs………………………5 6. Discussions and recommendations…………...6 7. References……………………………………..6

INTRODUCTION

Concrete is one of the most commonly used structural materials. It is made by simply mixing cement, aggregate, sand and water in the “right” proportion. The strength of concrete varies even with the slightest variation in the ratio or quality of its ingredients. Concrete properties are highly influenced by the water type used and its proportion in the concrete mix, but actually there is little knowledge of the effects of different, alternative water sources used in concrete mix design. Therefore, the identification of the level and nature of contamination in available water sources and their subsequent influence on concrete properties is becoming increasingly important.

OBJECTIVE
In general, the increasing industrial activity and the rising cost of natural mineral resources, and forcing the ready mixed concrete industry to review the logistics of raw material supply. A lack of potable water, an integral constituent of concrete has resulted in search for possible alternatives. While almost any natural water that is drinkable and has no pronounced taste or odour may be used as mixing water for concrete, the rising cost of such water has prompted many researchers to experiment with salt water in concrete. The



References: 3. Technical report, R306, the effect of salt in concrete on compressive strength, water vapour transmission and corrosion of reinforcing steel, 22 July, 1964

You May Also Find These Documents Helpful

  • Powerful Essays

    Objective : To determine the characteristic strength of the concrete and comparison between group 20 and group 25.…

    • 1186 Words
    • 5 Pages
    Powerful Essays
  • Satisfactory Essays

    How does salt damage concrete surfaces? Salt lowers the pH balance in the concrete. Because it is acidic, it weakens the strength of the concrete and increases the sizes of the pores. This allows water and other elements to penetrate the surface. Salt also attracts and retains water, absorbing 10% more water into the concrete. When the water freezes in the concrete, the pressure of frozen water increases. This causes pits, cracks,…

    • 282 Words
    • 2 Pages
    Satisfactory Essays
  • Good Essays

    Concrete Technology

    • 1367 Words
    • 6 Pages

    III B.Tech. I Semester Regular Examinations, November/December - 2012 CONCRETE TECHNOLOGY (Civil Engineering) Time: 3 Hours Max Marks: 75 Answer any FIVE Questions All Questions carry equal marks ***** Assume missing data suitably 1. (a) Describe the oxide composition of Ordinary Portland Cement. (b) What are the main compounds into which the above oxides will transform in the process of fusion?. 2. (a) Explain the phenomenon of bulking of fine aggregates and its practical significance in mix proportioning. (b) Explain Alkali-aggregate reaction and its effect on the final product of concrete. 3. (a) List out various field and laboratory tests that are conducted to assess the properties of fresh concrete. (b) Explain Compaction Factor test describing the test equipment. Compare the Compaction factor values to Slump of the concrete for different workability. 4. (a) Explain Plowman’s procedure for assessment of maturity of concrete. (b) The strength of a sample of fully matured concrete is found to be 40Mpa. Find the strength of identical concrete at age of 7 days when cured at an average temperature during daytime at 180 and night time at 90 centigrade. The plowman’s constants A and B are 32 and 54 respectively. 5. (a) What are the factors affecting the strength of concrete? (b) Explain the procedure for measuring split tensile strength. 6. (a) Explain phenomenon of creep in concrete. Explain measurement of creep in creep with loading diagram. (b) Explain various factors influencing creep in concrete. 7. (a) Explain with neat diagram non-destructive evaluation of concrete using Pulse Velocity Method. (b) What are the techniques of measuring pulse velocity through concrete and factors affecting the measurement of pulse velocity? 8. (a) Explain significance of concrete mix design. What are various factors to be kept in mind while designing a concrete mix? (b)…

    • 1367 Words
    • 6 Pages
    Good Essays
  • Powerful Essays

    Study on Pump

    • 16216 Words
    • 65 Pages

    This report describes pumps for transporting and placing concrete. Rigid and flexible pipelines are discussed and couplings and other accessories described. Recommendations for proportioning pumpable concrete suggest optimum gradation of aggregates; outline water, cement, and admixture requirements; and emphasize the need for evaluation of trial mixes for pumpability. The importance of saturating lightweight aggregates is stressed. Suggestions are given for layout of lines; for maintaining uniform delivery rate, as well as uniform quality of concrete at the end of the line; and for cleaning out pipelines. This report does not cover shotcreting or pumping of nonstructural insulating or cellular concrete. Keywords: admixtures; aggregate gradation; aggregates; cement content; coarse aggregates; concrete construction; concretes; conveying; couplings; fine aggregates; fineness modulus; lightweight aggregate concrete; lightweight aggregates; mix proportioning; pipeline; placing; placing boom; pozzolans; pumped concrete; pumps; quality control; water content.…

    • 16216 Words
    • 65 Pages
    Powerful Essays
  • Powerful Essays

    concrete technology cc203

    • 3940 Words
    • 16 Pages

    Concrete is strong, durable and economical material whose appearance can be altered in many ways to make it decorative as well as functional.…

    • 3940 Words
    • 16 Pages
    Powerful Essays
  • Best Essays

    Corrosion

    • 2794 Words
    • 12 Pages

    As consequence, this report is prepared in order to identify the most common causes of steel corrosion in reinforced concrete, its mechanics and how this process affects its structural performance. Furthermore, this paper will explore certain remedial approaches, as well as preventive measures against corrosion.…

    • 2794 Words
    • 12 Pages
    Best Essays
  • Satisfactory Essays

    Shri

    • 1015 Words
    • 5 Pages

    Category Credits Departmental Electives (DE) Credits CED310 CEL311 CEL341 CEL362 CEL411 CEL412 CEL421 CEL422 CEL423 CEL431 CEL432 3-1-0 0-0-8 3-1-0 3-1-0 3-1-0 0-0-4 12-4-8 4 4 4 4 4 2 20 CEL433 CEL442 CEL443 CEL451 CEL453 CEL455 CEL459 CEL464 CEL466 CEP452 CED412 Mini Project (CE) Advanced Water and Wastewater Engineering Transportation Engineering – II Construction Management Industrial Waste Management Environmental Assessment Methodologies Ground Improvement Rock Engineering Designs of Foundation, Earth and Earth Retaining Structures Advanced Structural Analysis Design of Prestressed Concrete and Industrial Structures Advanced Structural Design Traffic and Transportation Planning Transportation Safety and Environment Water Power Engineering Water Resources Management Introduction to Geographic Information Systems River Mechanics Construction Contract and Economics Construction Equipment and Methods Computational Aspects in Water Resources Major Project Part 2 (CE) 0-0-6 3-0-2 3-1-0 3-1-0 3-0-0 3-0-0 3-0-2 3-0-0 3-1-0 2-0-2 3-0-2 3-0-2 2-1-0 3-0-0 3-0-2 3-1-0 2-0-2 2-0-2 2-1-0 2-1-0 1-0-4 0-0-16 3 4 4 4 3 3 4 3 4 3 4 4 3 3 4 4 3 3 3 3 3 8…

    • 1015 Words
    • 5 Pages
    Satisfactory Essays
  • Powerful Essays

    local sand with a top size of 0.0236 in. (600 μm), and locally available Type I/II cement…

    • 4613 Words
    • 19 Pages
    Powerful Essays
  • Good Essays

    Concrete mixtures can be designed to provide a wide range of mechanical and durability properties to meet the design requirements of a structure. The compressive strength of concrete is the most common performances measure used by engineer in designing buildings and other structures. The compressive strength is measured by breaking concrete specimen in a compression-testing machine. The compressive strength is calculated from the failure load divided by the cross-sectional area resisting the load and reported in units of N/mm2. Compressive strength test results are primarily used to determine that the concrete mixture as delivered meets the requirements of the specified strength, in the job specification. Compressive strength is often measured on a universal testing machine; these range from very small table top systems to ones with over 53 MN capacity. Measurements of compressive strength are affected by the specific test method and conditions of measurement. Compressive strengths are usually reported in relationship to a specific technical standard. When a specimen of material is loaded in such a way that it extends it is said to be in tension. On the other hand if the material compresses and shortens it is said to be in compression. On an atomic level, the molecules or atoms are forced apart when in tension whereas in compression they are forced together. Since atoms in solids always try to find an equilibrium position, and distance between other atoms, forces arise throughout the entire material which oppose both tension and compression. The phenomena prevailing on an atomic level are therefore similar. On a macroscopic scale, these aspects are also reflected in the fact that the properties of most common materials in tension and compression are quite similar. The major difference between the two types of loading is the strain which would have opposite signs for tensile and compression. Another major difference is tension tends to pull small…

    • 873 Words
    • 4 Pages
    Good Essays
  • Powerful Essays

    transport aspects. The third part is about academic skill restriction. On the face of it,…

    • 1822 Words
    • 4 Pages
    Powerful Essays
  • Good Essays

    Water Absorption Test

    • 280 Words
    • 3 Pages

    06/11 Water Absorption ASTM C 140 Water Absorption One of the most important properties of a good quality concrete is low permeability, especially one resistant to freezing and thawing. A concrete with low permeability resists ingress of water and is not as susceptible to freezing and thawing. Water enters pores in the cement paste and even in the aggregate. Absorption For concrete pavers, the test procedure involves drying a specimen to a constant weight, weighing it, immersing it in water for specified amount of time, and weighing it again. The increase in weight as a percentage of the original weight is expressed as its absorption (in percent).…

    • 280 Words
    • 3 Pages
    Good Essays
  • Good Essays

    Nao Silica Case Study

    • 1334 Words
    • 6 Pages

    Cement paste and mortar with Nano Silica addition needs more water in order to keep the workability of the mixtures constant. Test results have shown that Nano Silica can improve the microstructure and reduce the water permeability of hardened concrete. Microstructural analysis of concrete by different electronic microscope techniques revealed that the microstructure of the Nano Silica concrete is more uniform and compact than for normal concrete. The Nano Silica particles fill the voids of the CSH-gel structure and act as nucleus to tightly bond with CSH-gel particles therefore increases durability. The addition of Nano Silica increases density, reduces porosity, and improves the bond between cement matrix and aggregates which produces concrete that shows higher compressive and flexural…

    • 1334 Words
    • 6 Pages
    Good Essays
  • Better Essays

    limitation and low performance of cement. The mixture, however, is hard to avoid because there…

    • 727 Words
    • 5 Pages
    Better Essays
  • Satisfactory Essays

    Oyster Shell

    • 250 Words
    • 1 Page

    In this study to evaluate the possibility of recycling this waste for use as a construction material, the mechanical characteristics of pulverized oyster shell were investigated in terms of its potential utilization as a substitute for the aggregates used in mortar. The unconfined compressive strengths of various soil mortar specimens, with varying blending ratios of cement, water and oyster shell, were evaluated by performing unconfined compression tests, and the results were compared with the strengths of normal cement mortar made with sand. In addition, the effect of organic chemicals on the hardening of concrete was evaluated by preparing ethyl-benzene-mixed mortar specimens. The long-term strength improvement resulting from the addition of fly ash was also examined by performing unconfined compression tests on specimens with fly-ash…

    • 250 Words
    • 1 Page
    Satisfactory Essays
  • Good Essays

    Ingredients for concrete are cement, fine aggregate, coarse aggregate and water. The best concrete can be obtained by mixing the ingredients in correct proportions. The ideal proportion of concrete will be that, which produces greatest strength and solidity at the least cost. In estimating the quantities of ingredients for cement concrete it should keep in mind that voids of coarse aggregates are filled up by sand and voids of fine aggregates are filled up by cement. The concrete mix of 1: 1: 2 and 1: 11/2: 3 are mostly used for water retaining structures. The concrete mix 1: 2: 4 is most commonly used for R.C.C. construction. The mix proportion of 1: 3: 6 and 1: 4: 8 are used in lean concrete works. The concept behind the proportioning of concrete mixes is that the resulting concrete is densest and strongest with least amount of cement. Following are the methods of proportioning concrete:…

    • 473 Words
    • 2 Pages
    Good Essays

Related Topics